[Dec-2023] 300-410 Braindumps – 300-410 Questions to Get Better Grades
300-410 Exam Dumps - Try Best 300-410 Exam Questions - ExamTorrent
Cisco 300-410 certification exam consists of 60-70 multiple-choice and simulation questions. 300-410 exam duration is 90 minutes, and candidates must score at least 750 out of 1000 to pass the exam. 300-410 exam can be taken at any Pearson VUE testing center worldwide, and the cost of the exam may vary depending on the location.
Cisco 300-410 certification exam is designed to validate the knowledge and skills of IT professionals who are responsible for implementing and managing advanced routing and services in Cisco enterprise networks. 300-410 exam covers a range of topics, including network architecture, routing protocols, VPNs, network security, and automation. Passing 300-410 exam demonstrates that the candidate has the expertise required to design, implement, and troubleshoot complex enterprise networks.
NEW QUESTION # 104
Refer to the exhibit.
Refer to the exhibit. An engineer examines the BGP update for the IPv6 prefix 2001:db8::1/128. which should have been summarized into a /64 prefix. Which sequence of actions achieves the summarization?
- A. R1 is a route reflector client of a RR with a router ID of 1.1.1.1. and the originator of the prefix has a router ID of 3.3.3.3. Both routers belong to different ASs. The prefix is not advertised to any peer and must be advertised using the network statement on R3.
- B. R1 is a route reflector with a router ID of 3.3.3.3. and the originator of the prefix is a route reflector client, which has a router ID of 3.3.3.3. Both routers belong to the same AS Configure an aggregate address on the router with ID 1.1.1.1 for the prefix
- C. R1 is a route reflector client of a RR with a router ID of 1.1.1.1. and the originator of the prefix has a router ID of 3.3.3.3. Both routers belong to the same AS. Configure an aggregate address on the router with ID 3 3.3.3 for the prefix.
- D. R1 is a route reflector with a router ID of 1.111. and the originator of the prefix is a route reflector client, which has a router ID of 3.3.3.3. Both routers belong to the same AS Configure an aggregate address on the router with ID 1.1.1.1 for the prefix
Answer: C
NEW QUESTION # 105 
- A. snmp-server group NETADMIN v3 priv read NETVIEW write NETADMIN access 22
- B. snmp-server group NETVIEW v2c priv read NETVIEW access 20
- C. access-list 20 permit 10.221.10.11
- D. access-list 20 permit 10.221.10.12
Answer: C
NEW QUESTION # 106
Refer to the exhibit.
A network engineer applied a filter for LSA traffic on OSPFv3 interarea routes on the area 5 ABR to protect advertising the internal routes of area 5 to the business partner network. All other areas should receive the area 5 internal routes. After the respective route filtering configuration is applied on the ABR, area 5 routes are not visible on any of the areas. How must the filter list be applied on the ABR to resolve this issue?
- A. in the "in" direction for area 20 on router R2
- B. in the "in" direction for area 5 on router R1
- C. in the "out" direction for area 20 on router R2
- D. in the "out" direction for area 5 on router R1
Answer: C
NEW QUESTION # 107 
Refer to the exhibit. The administrator configured route advertisement to a remote low resources router to use only the default route to reach any network but failed. Which action resolves this issue?
- A. Remove the line with the sequence number 10 from the prefix list.
- B. Remove the prefix keyword from the distribute-list command.
- C. Remove the line with the sequence number 5 from the prefix list.
- D. Change the direction of the distribute-list command from out to in.
Answer: C
NEW QUESTION # 108
Refer to the exhibit.
Which configuration configures a policy on R1 to forward any traffic that is sourced from the 192.168.130.0/24 network to 17.20.20.0/30 network?
A)
B)
C)
D)
- A. Option C
- B. Option A
- C. Option B
- D. Option D
Answer: D
NEW QUESTION # 109
What is a function of IPv6 Source Guard?
- A. It inspects ND and DHCP packets to build an address binding table.
- B. It works with address glean or ND to find existing addresses.
- C. It denies traffic from known sources and allocated addresses.
- D. It notifies the ND protocol to inform hosts if the traffic is denied by it.
Answer: B
Explanation:
IPv6 source guard is an interface feature between the populated binding table and data traffic filtering. This feature enables the device to deny traffic when it is originated from an address that is not stored in the binding table. IPv6 source guard does not inspect ND or DHCP packets;rather, it works in conjunction with IPv6 neighbor discovery (ND) inspection or IPv6 address glean, both of which detect existing addresses on the link and store them into the binding table.
NEW QUESTION # 110
The implementations group has been using the test bed to do a 'proof-of-concept' that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing scheme, DHCP services, NTP services, and FHRP services, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address.
Use the supported commands to isolated the cause of this fault and answer the following questions.
The fault condition is related to which technology?
- A. Access Vlans
- B. NTP
- C. Port Security
- D. VLAN ACL / Port ACL
- E. Switch Virtual Interface
- F. Switch-to-Switch Connectivity
Answer: F
Explanation:
Since the Clients are getting an APIPA we know that DHCP is not working. However, upon closer examination of the ASW1 configuration we can see that the problem is not with DHCP, but the fact that the trunks on the port channels are only allowing VLANs 1-9, when the clients belong to VLAN 10. VLAN 10 is not traversing the trunk on ASW1, so the problem is with switch to switch connectivity, specifically the trunk configuration on ASW1.
NEW QUESTION # 111
Refer to the exhibit.
Which interface configuration must be configured on the HUB router to enable MVPN with mGRE mode?
- A. Option D
- B. Option C
- C. Option A
- D. Option B
Answer: B
Explanation:
https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/sec_conn_dmvpn/configuration/15-mt/sec-conn-dmvpn-15-mt-book/sec-conn-dmvpn-dmvpn.html
NEW QUESTION # 112
An engineer configured access list NON-CISCO in a policy to influence routes
What are the two effects of this route map configuration? (Choose two.)
- A. Packets are forwarded using normal route lookup.
- B. Packets are not evaluated by sequence 10.
- C. Packets are forwarded to the default gateway.
- D. Packets are dropped by the access list.
- E. Packets are evaluated by sequence 10.
Answer: D,E
Explanation:
Explanation
https://www.cisco.com/c/en/us/support/docs/ip/ip-routed-protocols/47121-pbr-cmds-ce.html
NEW QUESTION # 113
Refer to the exhibit.
An engineer is trying to block the route to 192.168.2.2 from the routing table by using the configuration that is shown. The route is still present in the routing table as an OSPF route. Which action blocks the route?
- A. Use an extended access list instead of a standard access list.
- B. Add this statement to the route map: route-map RM-OSPF-DL deny 20.
- C. Use a prefix list instead of an access list in the route map.
- D. Change sequence 10 in the route-map command from permit to deny.
Answer: D
NEW QUESTION # 114
An engineer is configuring a network and needs packets to be forwarded to an interface for any destination address that is not in the routing table. What should be configured to accomplish this task?
- A. set ip next-hop
- B. set ip default next-hop
- C. set ip next-hop verify-availability
- D. set ip next-hop recursive
Answer: B
Explanation:
NEW QUESTION # 115
Drag and drop the descriptions from the left onto the corresponding MPLS components on the right.
Answer:
Explanation:
NEW QUESTION # 116
Refer to the exhibit.
An engineer must redistribute networks 192.168.10.0/24 and 192.168.20.0/24 into OSPF from EIGRP. where the metric must be added when traversing through multiple hops to start an external route of 20 The engineer notices that the external metric is fixed and does not add at each hop. Which configuration resolves the issue?
- A. Option D
- B. Option C
- C. Option B
- D. Option A
Answer: C
NEW QUESTION # 117
Refer to the exhibit.
Drag and drop the credentials from the left onto the remote login information on the right to resolve a failed login attempt to vtys. Not all credentials are uf SLA by defining frequency and schedulingsed
Answer:
Explanation:
Explanation:
vty 0:
+ cisco
+ 0csic
vty 1:
+ no username
+ no password
The command "aaa authentication login default none" means no authentication is required when access to the device via Console/VTY/AUX so if one interface does not specify another login authentication method (via the "login authentication ..." command), it will allow to access without requiring username or password. In this case VTY 1 does not specify another authentication login method so it will use the default method (which is "none" in this case).
NEW QUESTION # 118
Refer to the exhibit. An engineer is trying to connect to a device with SSH but cannot connect. The engineer connects by using the console and finds the displayed output when troubleshooting.
Which command must be used in configuration mode to enable SSH on the device?
- A. ip ssh enable
- B. ip ssh version 2
- C. crypto key generate rsa
- D. no ip ssh disable
Answer: C
Explanation:
Section: Infrastructure Security
NEW QUESTION # 119
......
Verified 300-410 exam dumps Q&As with Correct 563 Questions and Answers: https://vcetorrent.examtorrent.com/300-410-prep4sure-dumps.html
